Care For Kirpan

[GurburAkal]

I have a pretty long taksali sri sahib. It looks very nice, but the problem is that the handle part at the end where you hold it from has many scratches and slowly it is becoming kinda dark and stuff. Is it okay if I add a sort of leather grip on the handle to protect from damage? Will it cause any problems with the iron? Does anyone with knowledge in this kinda stuff tell me how to add one myself?

If that is not possible, then does anyone know of a way to remove the scratches and give it a brand new look?

My kirpan looks exactly like this:

https://www.facebook.com/Lsnaagi/photos/a.639552042834228.1073741842.238662012923235/688275261295239/?type=1&theater

Please give me other tips on kirpan maintenance too

[hsingh8963]

Do you have any idea where the scratches are coming from?

You can clean the Sri Sahib To keep it nice...

Leather Grip seems like an ok idea...

But if you wanna keep the original look you can just make a cover that can slip onto the handle.

[hsingh8963]

Rust Prevention & Removal

Rust may be removed from your Kirpans by either chemical or abrasive cleaning. Regardless of method, cleaning has its risks. Proceed with caution. Improper use or attention may damage your blades and/or their temper.

Rust Prevention

All exposed steel will want to rust. Touching any exposed steel, such as your blade, with your bare hands will leave oils and salts that will eat their way into your blade and eventually leave pits. The best way to avoid this is not to touch the blade and to wipe off the blade if it is touched. It is also a good idea to inspect your Kirpans at least annually to check for new rusty areas and to use fine steel wool or Nev-R-Dull on them. Don't forget to change the oil, too.

Rust Removal

I know of two methods of cleaning the rust off of steel -- chemicals and abrasion. I'll try to give several examples of each, in order of weakest method to harshest. Always start with something weak -- it's easier to take rust off than to put steel back on. BTW, we haven't tried most of these, and use caution with any chemicals. (When in doubt always have your Kirpans professionally cleaned.)

Chemical Cleaning

You can use a Kirpan Cleaning Kit or Nev-R-Dull for a mild chemical cleaner. It removes light surface rust and dirt, and is safe to use. It is available at your local automotive store and I believe it is cotton with a penetrating oil. It is oily feeling and leaves a slight residue on anything it is rubbed against. Rub the rusty area with a small piece and then wipe it off. Great for removing rust caused by light handling or humidity. Always test it on a small area if in doubt. Not recommended for blued blades (haven't tried it).

Acids. Yup, you read that right, just be careful and go slow. Start with some mild household acids -- try lemon juice first. It may take a few days, but check it periodically. Next would be vinegar (mild ascetic acid), and then Worcestershire sauce. My preference is a mild solution of carbonic and phosphonic acids that goes by the trade name of Diet Pepsi (takes about 3 days, followed by some steel wool and nev-r-dull). If those don't work, A 1 molar solution of a medium-strong acid, such as muriatic or phosphonic acid, will slowly eat away the rust. Check your pool supply store for these. They may take a few hours, but check them regularly! They will eventually eat into the blade if left too long. Strong HCl will eat the rust off in seconds (I use it to clean rusty tools at work), but I do not recommend this method for use on a Kirpan. A strong acid will leave microscopic etching, which will give a dull, leaden look to the blade.

Electrolysis is the process of breaking apart the rust molecules into iron and oxygen, then binding the oxygen to a more active metal. One method is to immerse the blade (remove the handle first) in a slightly basic solution (caustic soda or lye) while it is surrounded with metallic zinc. The reaction will eat the rust and produce zinc oxide. It is important that a basic solution is used to prevent further rusting of the steel, and make sure that the surface to be oxidized is a more active metal than iron. Check a college chemistry book when in doubt.

Do not use aluminium foil, because it is more stable than iron and will cause the iron to rust away. The process takes a few hours, so check it regularly. The process can be speeded up by connecting a car battery to the apparatus as such: negative to iron, positive to zinc. I have been told that electrolysis can leave a blade looking 'cooked,' and that it destroys the original temper of the blade.

I've also been told that exposure to high heat will remove rust, but this will discolour the blade and destroy the temper.

Abrasive Cleaning

Oil and steel wool is the most often prescribed way to remove light surface rust. You know how to use it already, so there is no need to say more. Scotch-brite pads and olive oil make a good alternative, for the more kitchen inclined collectors. Rubbing the steel with a piece of copper will remove rust as well. Since copper is softer than iron, it won't scratch the surface, either. I have never tried it before, but I don't think it would take off any patina.

A soft wire brush works the same way, and may be useful for a Kirpan that is already heavily pitted or scaled with rust. The bristles shouldn't put enough pressure on the steel to scratch it, so it should be ok. I have seen wire wheels for drills, and they might work as well. Test it on a small area first before attacking the whole blade.

Polishing stones are used in knife making, and will give a mirror finish to the blade. Remember, though, that this may actually detract from the value of the Kirpan. Also remember this -- it takes a 5-year apprenticeship to learn to make a Japanese Kirpan, and a 10-year apprenticeship to learn to polish one. 'Nuff said.

I assume that abrasive cleaning compounds might work, but that they would leave scratches on the blade. Test a few out if you want to try this method. Very fine grit sandpaper will leave scratches, but it is good for a hard assault on scaled rust. Be careful to only be rubbing the rust, though.

Kirpan Storage & Feeding

Just because you don't own a museum-quality display case doesn't mean that your Kirpans are at the mercy of the elements. Lacking a museum-quality temperature and humidity controlled lockable display case does not mean that your collection can't be displayed safely. The average collection is not damaged by being hung on a wall with steel hooks (not aluminium) or on wooden display racks. In high humidity areas, though, it is best to keep your collection stored in a sealed case with enough dessicant to keep the humidity beneath about 30% to hinder rust. It is also very important to KEEP KIRPANS OUT OF THE HANDS OF CHILDREN. Children will destroy a Kirpan in a fraction of the time it takes rust. Also keep Kirpans out of reach of people who want to clash blades like in the movies or cut down trees with them.

Long Term Storage

If you do not wish to display your Kirpans, the most important ways to protect your collection are to protect it from rust, skin contact, and theft. A gun safe will protect it from all of these. If that route is unavailable, however, we recommend either using a gun sock or making a Kirpan bag. In either case, we recommend placing a few packages of desiccant in with the Kirpan to keep humidity down.

Care for the blade

Your blade, being steel, will appreciate regular coats of a clear, non-organic, oil. This prevents moisture from reaching the blade, as well as giving a nasty sliming to anyone who touches it. We recommend a light oil such as sewing machine oil. We've heard of using 10W40, but can't comment as its usefulness. Oil should be changed regularly by wiping the blade with a soft cloth until dry, then applying more.

Cosmoline, a Vaseline like substance, and grease were often used in the past, but now are getting looked down upon. If you have an old blade covered in it, rest assured that it will still be protected, but there may be microscopic pits in the blade that would make a collector of Japanese Kirpans cringe. The stuff is quite ugly as well, but at least it keeps hands off.... Another option is to apply a wax coating. Renaissance wax is a wonderful option that is used by museums. We've also heard of using carnauba wax (like on your car), but cannot comment to its long term effects. You might want to check your local automotive store/department to ask about which waxes are best on steel.

The final viable option is a clear varnish. Del Tin, a respected maker of medieval replica swords, puts a coat of varnish on their sword blades. We recommend making sure there are no fingerprints or specks of dust on the blade first, or else they will eat into the blade from beneath the coating.

Handle and Scabbard Coatings

We still don't know of any accepted long-term protective coatings for leather scabbards and handles. Any help would be appreciated.

http://www.sikhiwiki.org/index.php/Caring_for_the_kirpan#Kirpan_Maintenance